Archive

Category Archives for "Blog"

Fixing a Leaking Washer With Las Vegas Appliance Masters

Today we’re looking at a Whirlpool top load washer; the customer complaint was water leaking onto the floor from the washer. Upon moving the washer out and inspecting, find out where the water was coming from, we found the siphon break on the drain hose was leaking when the washer would drain. To us, this is a job for the pros at Appliance Repair Las Vegas (http://lasvegasappliancemasters.com), who were kind enough to help us through this repair job.

There’s a gasket inside here so when the water drains, it’s supposed to seal the gap here from the drain hose and then when the water’s gone the plunger seal goes back down, allows air to come into the drain hose, that gives that the siphon break. So, the gaskets just worn and water is leaking out at the top here when it drains so we’re going to be installing new siphon break.

The tools needed for this repair are five sixteenths nut driver or your drill with the five sixteenths chuck and a pair of multi-purpose cutters.

STOP!

Before beginning any repair, always be sure to disconnect the power to the appliance.

It is also recommended to test the outlet for proper voltage. Remember to also turn off the water.

So we’ll just have to remove our two hose clamp holding siphon break on. This is a five sixteenths nut driver. And now we can just pull our drain hose of the siphon break. We’ll just going to remove the drain hose sleeves from the drain hose.

From where the original siphon break was installed and the hose clamp was installed, you can see the part of the hose that is damaged, so we’re going to go ahead and cut that back and remove the damaged section.

Just use a pair of multi-purpose cutters. The next step is to install the new drain hose sleeves. We’re going to go ahead and place one of our drain hose clams onto the drain hose and now the siphon break.

Now the siphon break is installed into the drain hoses we can install the new hose clamps that were provided in the kit. We’ll just going to tighten the five sixteenths with the nut driver.

And the next they we’re going to do is secure our drain hose assembly to the back of the washer can with the zip tie, this is also provided in the kit. At this point your repairs complete the only thing left to do is to run the washer to recycle and check your connections for water leaks.

If you’re getting a very low reading and you have verified all the things that I listed before, the pressure switch, the temperature switch, and the timer cycle setting, than you might need to check out the “Under the Console” chapter. If the valve seems to be receiving power, but it is not opening fully, it is likely bad internally and needs to be replaced. Check the valve screens for debris. If they are mostly clean than the plunger to the valve is probably bound up and not opening fully and needs to be replaced.

To replace the valve, unplug the washer, remove all wire plugs, remove any mounting screws, raise the valve up out of its cradle, and then remove the tub supply (?). Some new valves come with a plate that can be installed on the valve and make it compatible with many models of washers produced over the years. Reinstall the new valve with your trusty nut driver. Reinstall any screws that you may need. Reinstall your power supply wires. Wire terminals are usually color coded and fool proof. Red would be for hot and white would be for cold. Reattach the tub supply line and all of your hoses. You might want to check to see if the washer will fill properly before you reinstall the cabinet.

A Few Thing to Remember:
• The water valve should open when supplies with 120 volts
• The valve should open and close completely
• The valve is supplied power from the timer through the temperature switch and pressure switch

Strategies For Doing Your Own Home Improvements

Tools You’ll Be Able To Trust: How To Tips For The Homeowner

Damaged, bent, or rusted metal railings are among the very offensive eyesores generally seen on older houses. For a modern look that does not upstage the classic exterior of your home, replace metal railing with textured wood supports. You can stain the wood a color that is darker or leave it natural contingent on your house’s outdoor color.

Clean up the outside of your house. All it takes to make your home look and feel is a little TLC on the outside. Trim the shrubs and pull the weeds of the flower bed. Add some cosmetic landscape lighting and ensure each of the outside light fixtures are in proper working order.

A great method to lessen your chance of mold growth in your household is by making sure your bathroom is well ventilated. Toilets which do not have some kind of vent or a window generally get steamy, but are not able to be rid of the humidity. This humidity leads to extensive mould development.

A staple tool to have is your drill if you’re going to do any home improvements. You require it to drive them in place and to begin screws. Ensure you have a drill that is cordless and battery used with a minimum of 9 volts. You should also have drill bits of numerous sizes and screw fasteners.

Smoke detectors are needed for security in your house. Many residences just put them in particular areas. It’s possible for you to increase the safety in your home, by installing additional sensors in areas like kitchens, toilets and cellars. These regions can sometimes be overlooked, though prone to fires as much or more compared to the remainder of the house.

If you’re selecting a major restoration, employ a professional designer or architect to help develop the plans. In case a part of your family or you don’t have professional training in this area, a professional designer will be able to produce a strategy that also matches all required building codes.

Consider converting fresh rooms within your house. Before you spend too much cash adding an additional room or two to your home , seriously look at what you need to work with. Are you getting much use out of that exercise office or room? Even storage spaces like attics could be transformed into something useful, like a bedroom.

Enhance your home by removing items you don’t want. You may have more space as well as your house will appear to be larger. De-litter by donating unneeded items for example clothes, furniture, etc., storing or throwing away Even packing your stuff away in boxes and putting those in the attic will remove things from your immediate living place.

 

 

Want to Do It Yourself? Here’s Some Tips For The Beginning Handyman

home repairs merit badgeA new replacement deck can be a great improvement to your home, but you have to be on the lookout for the common telltale signals that signify your deck is due for care. See the way the wood is holding up and that there aren’t any cracks. See if there is any sign of rot. Check to determine whether there are any nails.

Choose two easy-to-recall the batteries in your carbon monoxide and smoke detectors and replace, if needed, days of the year to check. New Year’s Day and the Fourth of July are perfect times to perform this job. You discuss your family’s exit strategy in case of a fire and should also make certain that your fire extinguishers work.

A dripping sink might be an annoyance in just about any home. It not only wastes water, but costs money on your own water bill. The faucets central cartridge might need to be replaced, if there is a sink dripping from the spout. When you have a column tap, you may want to change the washer. A quick examination will allow you to discover your course of action.

Glue your wallboard in position before nailing it! A caulking gun and the right adhesive makes fast work of the occupation. Faster installation’s advantages are clear. Another advantage is fewer nails. Furthermore, the adhesive holds the wall board tightly in place and the nails you do use are less likely to pop out later on.

Seriously reconsider adding a swimming pool to your backyard. A pool may be a pleasant addition to a home. What some people don’t see is that they are also rather pricey. There’s also the price of regular upkeep, not only are there the initial costs to think about. Make sure you have time and the cash needed, to keep your pool area from falling into disrepair, before you spend the cash on it. If you have doubts… sneak a peek at this web-site.

Trimming your hedges, trees and bushes may not be the very first thing which comes to mind when the appearance of your property can significantly improve. It can often be a quick day job for you to undertake, that’ll bring about a nice, finished look.

Store it in a glass jar instead of leaving it in the paint can, in case you have extra paint left over from a recent endeavor. You will have the ability to immediately tell what the color is without going through the messy ordeal of opening the lid of the paint can.

 

 

Cleaning Grout Tip – Powerful and Easy To Do

Today I’ve got one question for you and one huge cleaning tip. The question is this: “What is the best way to clean out grout?” It’s the Holy Grail of cleaning questions, right? Or at least it seems to be the case. One of my awesome fans, Ashley Self, submitted this great cleaning tip, and it has to do with this little invention she likes to call the Grout Grime Buster 3000.

And today, I am going to show you how to build this little fellow for less than $5.00. It’s going to make cleaning, not only your grout, but your kitchen and your bathroom and your laundry room, you name it, so much easier, quicker, and better. So let’s get started. In order to make the Grout Grime Buster 3000, you need a few things. You need some soap dispensing palm brush refills like this. I bough this at Target for a few bucks.

You need a like this one. This is five inches long. You need a hex nut, a flat washer and two split washers. It’s pretty simply what you need to do. You need to put one of the split lock washers on the bolt and slide it through like so. The next step is to place a flat washer on the bolt and the second split lock washer. Slide your hex nut on there, get it snug. Use a crescent wrench and then a socket wrench to ratchet it down.

And that’s all you need to do to make the Grout Grime Buster 3000. You can stick it into your drill like so. Lock it in place. And now you’ve got the perfect grout or tile cleaning solution. In a previous experiment, I determined that one quarter cup of Oxi Clean added to two cups of warm water is the perfect tile and grout cleaning solution. Pour this solution onto your grout and tile.

Let it sit for 5-10 minutes, then use the Grout Grime Buster 3000 to remove all the grime and dirt. Check this out. This is what Ashley’s grout and tiles looked like before and after. And this is what my tile and grout looked like before and after I used the cleaning solution and the Grout Grime Buster 3000. Pretty impressive, right? But this is not the only place that you can use this awesome little device. You can use it in your kitchen.

You can use it in your laundry room. You can use it in your shower. You can use it for the tile in your shower. You can use it on your toilet. You can use it in your sink and many other places. It’s unbelievable!  I’m here to tell you that this… I don’t know why nobody came up with this before for such a cheap price. So you should totally check this out. Build Grout Grime Buster 300. And if you have your own cleaning idea, let me know because maybe I’ll make a video out of it too.

What do you think? Wasn’t that one of the best ways to clean grout? I think it was. If you have your own suggestion, please leave it in the comment section below because other DIY-ers or home repair tutors like myself will be able to share it with many home owners. And I think that it would benefit so many people. So please, leave you suggestion in the comment section below.